Det-tronics THZ HART Combustible Gas Transmitter Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Ekwipunek Det-tronics THZ HART Combustible Gas Transmitter. Det-Tronics THZ HART Combustible Gas Transmitter User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 8
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
DESCRIPTION
The DEC-THZ Toxic Gas Transmitter is a Class I,
Division 1 approved device when used with an
approved sensor, and is compatible with the entire
line of Det-Tronics electrochemical toxic gas sensors.
It provides a linear 4-20 mA output proportional to the
sensor input, as well as a large digital display for indi-
cating the detected gas level.
The model DEC-THZ Toxic Gas Detector is com-
prised of two assemblies:
•A Det-Tronics Model C7064X electrochemical gas
sensor, which is a two-wire, loop-powered gas sen-
sor providing a linear 4-20 milliampere output.
•A Model THZ Transmitter, which is specially config-
ured to accept the 4-20 mA signal from the
C7064X gas detector. The Model THZ provides
the HART signal along with the analog signal.
TRANSMITTER COMMUNICATION
The DEC-THZ transmitter output is ready for direct
interface with HART or non-HART based DCSs, PLCs,
and other computer-based SCADA systems. The
DEC-THZ is easily configured, monitored, or calibrat-
ed from anywhere on the 4-20 mA loop using a stan-
dard hand-held HART Communicator (such as a
Model HC275), a HART-based control system, or an
Asset Management System (AMS).
AUTOMATIC DIAGNOSTICS
The transmitter performs continuous sensor diagnos-
tics. If the sensor fails or otherwise stops sending a
signal during operation, the transmitter warns of a
trouble condition, and provides a HART digital error
message that can be read by a HART communicator
or system. The transmitter uses a modular electronics
design, which allows for easy removal and replace-
ment in the event of a malfunction.
TRANSMITTER ENCLOSURE
The transmitter’s aluminum enclosure features a
sealed, dual-compartment interior to isolate and pro-
tect the electronics from humidity, moisture, or corro-
sive agents that could possibly enter through the
cable conduit entry. The enclosure also has a screw-
on front cover with glass window to enable easy view-
ing of the detected gas level, and a screw-on rear
enclosure cover to enable easy access to the wiring
termination area. The enclosure provides two 3/4 inch
NPT conduit entries — one for the sensor, and one for
field cabling.
INSTRUCTIONS
Toxic Gas Detector
with HART Output
DEC-THZ
©Detector Electronics Corporation 2002 12/02 95-8550
DET-TRONICS
®
Przeglądanie stron 0
1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - DET-TRONICS

DESCRIPTIONThe DEC-THZ Toxic Gas Transmitter is a Class I,Division 1 approved device when used with anapproved sensor, and is compatible with the enti

Strona 2 - SPECIFICATIONS

SPECIFICATIONSDETECTION RANGE—Depends on sensor selected. Refer to form number90-1079 (Specification Data sheet for Det-Tronicselectrochemical sensor

Strona 3 - INSTALLATION

INSTALLATIONDETECTOR LOCATION AND ORIENTATIONThe gas sensor used with the THZ transmitter is a dif-fusion-based gas sensor. Therefore, it must contac

Strona 4 - CALIBRATION

CONFIGURATION USING HART COMMUNICATIONThe DEC-THZ gas detector is shipped from the facto-ry pre-configured. If it is necessary to change anyHART con

Strona 5 - 5 95-8550

Important Calibration Notes•Ensure that the transmitter is properly programmedfor the gas concentration being used for calibration.• Ensure that only

Strona 6 - MAINTENANCE

MAINTENANCEROUTINE MAINTENANCEThe DEC-THZ requires no routine maintenance,except for periodic checks to ensure proper calibra-tion. The frequency of

Strona 7 - ORDERING INFORMATION

5. Be sure that the O-ring inside the sensor base isin good condition, then re-install the cap. Tightenonly until snug. Do not over tighten.6. Re-ap

Strona 8 - ISO 9001

Detector Electronics Corporation6901 West 110th Street • Minneapolis, Minnesota 55438 USAOperator: (952) 941-5665 or (800) 765-FIRECustomer Service: (

Komentarze do niniejszej Instrukcji

Brak uwag